Please wait a minute...
材料研究学报  2020, Vol. 34 Issue (11): 822-828    DOI: 10.11901/1005.3093.2020.148
  研究论文 本期目录 | 过刊浏览 |
电子束辐射对取向性聚醚醚酮性能的影响
丁仁浩1,3, 曹丹2, 许璐1, 王自强1, 李建喜2, 马红娟1()
1.中国科学院上海应用物理研究所 上海 201800
2.中广核三角洲(太仓)检测技术有限公司 苏州 215400
3.中国科学院大学 北京 100049
Effect of Electron-beam Radiation on Properties of Oriented Poly (ether-ether-ketone)
DING Renhao1,3, CAO Dan2, XU Lu1, WANG Ziqiang1, LI Jianxi2, MA Hongjuan1()
1.Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800, China
2.CGN -DELTA (Taicang) Testing Technology Co. , Ltd. , Suzhou 215400, China
3.University of Chinese Academy of Sciences, Beijing 100049, China
引用本文:

丁仁浩, 曹丹, 许璐, 王自强, 李建喜, 马红娟. 电子束辐射对取向性聚醚醚酮性能的影响[J]. 材料研究学报, 2020, 34(11): 822-828.
Renhao DING, Dan CAO, Lu XU, Ziqiang WANG, Jianxi LI, Hongjuan MA. Effect of Electron-beam Radiation on Properties of Oriented Poly (ether-ether-ketone)[J]. Chinese Journal of Materials Research, 2020, 34(11): 822-828.

全文: PDF(4338 KB)   HTML
摘要: 

在室温空气气氛中用电子束(EB)辐照拉伸取向后的聚醚醚酮(PEEK)片,研究了辐射对取向性PEEK片材性能的影响。采用X射线衍射(XRD)、热重分析(TGA)、差示扫描量热(DSC)和万能拉力机等手段测试了不同辐射吸收剂量对取向性PEEK片受力方向(平行方向)和垂直于受力方向(垂直方向)的结晶性能、热稳定性、力学性能和热收缩性能的影响。结果表明,在实验吸收剂量范围内,样品的结晶温度、熔融焓以及结晶度都随着吸收剂量的增加而减小;随着吸收剂量的增加样品的热稳定性降低;在空气气氛中辐照样品,其平行和垂直方向上的断裂伸长率、断裂应力均随吸收剂量的增加而减小;辐照后样品平行方向的热收缩率是垂直方向的2倍,在不同吸收剂量的条件下两方向的热收缩率都不变。

关键词 有机高分子材料聚醚醚酮辐射老化热稳定性结晶行为    
Abstract

The effect of electron-beam (EB) radiation on the properties of oriented PEEK sheets in air at room temperature were investigated herein. While the effect of different absorbed doses of EB on the crystallinity, thermal stability, mechanical properties and thermal shrinkage properties of PEEK sheets in the direction of stress (parallel direction) and perpendicular to the direction of stress (vertical direction) was assessed by means of X-ray diffractometer (XRD), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and a universal tension machine. The results show that the crystallization temperature, melting enthalpy and crystallinity of the samples decreased with the increasing absorbed doses within the designed absorbed dose range. The thermal stability of the samples decreased with the increasing absorbed doses. The tensile stress and elongation at break in the parallel and vertical directions of the irradiated samples in air decreased with the increasing absorbed doses. The thermal shrinkage ratio of the samples after irradiation in the parallel direction was twice as high as that in the vertical direction, and was constant in these two directions under different absorbed doses.

Key wordsorganic polymer materials    poly(ether-ether-ketone)    radiation aging    thermal stability    crystallization behavior
收稿日期: 2020-05-03     
ZTFLH:  TL13  
基金资助:国家自然科学基金(U1732151)
作者简介: 丁仁浩,男,1996年生,硕士生
图1  PEEK片拉伸前后的取向情况
图2  不同吸收剂量辐照后取向性PEEK片的XRD谱图
图3  不同吸收剂量辐照后取向性PEEK片的TG和DTG曲线
SamplesT5%/℃T10%/℃TP /℃RM/%
PEEK/0 kGy568.0575.3586.147.2
PEEK/500 kGy567.9575.2585.949.5
PEEK/1000 kGy567.5574.3584.650.3
PEEK/1500 kGy566.8574.2584.351.6
PEEK/2000 kGy566.1573.4582.654.0
表1  不同吸收剂量辐照后PEEK样品的TGA数据
图4  不同吸收剂量辐照后取向性PEEK片的DSC曲线
SamplesTg/℃Tonset/℃Tpeak/℃Tc/℃H/J/gXC/%
PEEK/0 kGy149.5322.5337.8290.642.032.3
PEEK/500 kGy149.5322.1337.1290.438.129.3
PEEK/1000 kGy148.9321.7336.3290.036.828.3
PEEK/1500 kGy149.7320.6336.1289.136.528.1
PEEK/2000 kGy149.5320.1335.5288.336.127.8
表2  不同吸收剂量辐照后PEEK样品的DSC数据
图5  不同吸收剂量辐照后取向性PEEK片的断裂伸长率和断裂应力
图6  PEEK片取向过程晶体拉伸示意图
图7  用不同吸收剂量辐照后取向性PEEK片热收缩率的变化
1 Duan X Y. Application progress of special engineering plastics PEEK [J]. New. Chem. Mater., 2013, 41(05): 183
1 段翔远. 特种工程塑料聚醚醚酮应用进展 [J]. 化工新型材料, 2013, 41(05): 183
2 Zhang H, Fang L C, Chen Q H, et al. Application of PEEK in aerospace industry [J]. New Technology & New Process, 2018, 10: 5
2 张辉, 方良超, 陈奇海等. 聚醚醚酮在航空航天领域的应用 [J]. 新技术新工艺, 2018, 10: 5
3 Liu Z, Wang L, Hou X, et al. Investigation on dielectrical and space charge characteristics of PEEK insulation used in aerospace high-voltage system [J]. IEEJ Trans. Electr. Electron. Eng., 2020, 15(2): 172
4 Wang F Z, Jiang S Y, Zheng H, et al. Constructional design of class 1E cables for nuclear power station and investigation of related tests [J]. Electric Wire & Cable, 2006, 6: 14
4 王福志, 姜松奕, 郑红等. 核电站用1E级电缆结构设计及有关试验的探讨 [J]. 电线电缆, 2006, 6: 14
5 Zheng H, Wu X Y, Li Y M, et al. Remaining life prediction of class 1E cables by probabilistic reliability analysis [J]. Nucl. Sci. Eng., 2016, 36(03): 387
5 郑会, 乌晓燕, 李玉鸣等. 1E级电缆概率可靠性剩余寿命预测方法 [J]. 核科学与工程, 2016, 36(03): 387
6 Tan H R. Investigation on radiation effects of poly(ether ether ketone) under complicated conditions [D]. Shanghai: University of Chinese Academy of Sciences (Shanghai Institute of Applied Physics, Chinese Academy of Sciences), 2019
6 谭海容. 复杂条件下聚醚醚酮的辐照效应研究 [D]. 上海: 中国科学院大学(中国科学院上海应用物理研究所), 2019
7 Shi M, Gong Y, Xu J F, et al. Study on radiation aging properties and mechanism of PEEK special plastics [A]. Proceedings of 2015 National Failure Analysis Conference [C]. Beijing, 2015
7 时淼, 龚嶷, 徐剑峰等. PEEK特种塑料的辐照老化性能与机理研究 [A]. 2015年全国失效分析学术会议论文集 [C]. 北京, 2015
8 Zuo W, Xu D L, Bao M, et al. Extrusion process of PEEK insulated wire [J]. Optical Fiber & Electric Cable and Their Applications, 2012, 3: 36
8 左卫, 许德玲, 包明等. PEEK绝缘电线的挤出工艺 [J]. 光纤与电缆及其应用技术, 2012, 3: 36
9 Chen C Y, Zhang C, Zhao Z Q, et al. Effect of fiber reinforcement and fabrication process on the dynamic compressive behavior of PEEK composites [J]. Int. J. Mech. Sci., 2019, 155: 170
10 RodriguezCabello J C, Alonso M, Merino J C, et al. Scanning electron microscopy and differential scanning calorimetry study of the transition front in uniaxially stretched isotactic polypropylene [J]. J. Appl. Polym. Sci., 1996, 60(10): 1709
11 Liao T, Jiang Z Y, Li R, et al. Stretching temperature dependence of the critical strain in the tensile deformation of polyethylene copolymer [J]. Eur. Polym. J., 2017, 97: 188
12 Yoda O. The radiation effect on non-crystalline poly(aryl-ether-ketone) as revealed by X-ray diffraction and thermal analysis [J]. Polym. Commun., 1984, 25(8): 238
13 Yoda O. The crystallite size and lattice distortions in the chain direction of irradiated poly(aryl-ether-ketone) [J]. Polym. Commun., 1985, 26(1): 16
14 Woo E M, Tseng Y C. Glass transition and miscibility in blends of two semicrystalline polymers: Poly (aryl ether ketone) and poly(ether ether ketone) [J]. J. Polym Sci., Part B: Polym. Phys., 2015, 37(13): 1485
15 Goyal R K, Negi Y S, Tiwari A N. High performance polymer composites on PEEK reinforced with aluminum oxide [J]. J. Appl. Polym. Sci., 2006, 100(6): 4623
16 Mylläri V, Ruoko T P, Jarvela P. The effects of UV irradiation to polyetheretherketone fibres-Characterization by different techniques [J]. Polym. Degrad. Stab., 2014, 109: 278
17 Richaud E, Ferreira P, Audouin L, et al. Radiochemical ageing of poly(ether ether ketone) [J]. Eur. Polym. J., 2010, 46(4): 731
18 Wei C L, Chen M, Yu F E. Temperature modulated DSC and DSC studies on the origin of double melting peaks in poly(ether ether ketone) [J]. Polym., 2003, 44(26): 8185
19 Sasuga T, Kudoh H. Ion irradiation effects on thermal and mechanical properties of poly(ether-ether-ketone) (PEEK) [J]. Polym., 2000, 41(1): 185
20 Khare N, Limaye P K, Soni N L, et al. Gamma irradiation effects on thermal, physical and tribological properties of PEEK under water lubricated conditions [J]. Wear, 2015, 342: 85
[1] 姜水淼, 明开胜, 郑士建. 晶界偏析以及界面相和纳米晶材料力学性能的调控[J]. 材料研究学报, 2023, 37(5): 321-331.
[2] 叶姣凤, 王飞, 左洋, 张钧翔, 罗晓晓, 冯利邦. 兼具高强度、高韧性和自修复性能的环氧树脂改性热可逆聚氨酯[J]. 材料研究学报, 2023, 37(4): 257-263.
[3] 李瀚楼, 焦晓光, 朱欢欢, 赵晓欢, 矫庆泽, 冯彩虹, 赵芸. 支链含氟聚酯的合成和性能[J]. 材料研究学报, 2023, 37(4): 315-320.
[4] 马逸舟, 赵秋莹, 杨路, 裘进浩. 热塑型聚酰亚胺/聚偏氟乙烯全有机复合薄膜的制备及其介电储能[J]. 材料研究学报, 2023, 37(2): 89-94.
[5] 殷洁, 胡云涛, 刘慧, 杨逸霏, 王艺峰. 基于电沉积技术构建聚苯胺/海藻酸膜及电化学性能研究[J]. 材料研究学报, 2022, 36(4): 314-320.
[6] 申延龙, 李北罡. 磁性氨基酸功能化海藻酸铝凝胶聚合物的制备及对偶氮染料的超强吸附[J]. 材料研究学报, 2022, 36(3): 220-230.
[7] 崔丽, 孙丽丽, 郭鹏, 马鑫, 王舒远, 汪爱英. 沉积时间对聚醚醚酮表面类金刚石薄膜的结构和性能的影响[J]. 材料研究学报, 2022, 36(11): 801-810.
[8] 龙庆, 王传洋. 不同碳黑含量PMMA的热降解行为和动力学分析[J]. 材料研究学报, 2022, 36(11): 837-844.
[9] 蒋平, 吴丽华, 吕太勇, José Pérez-Rigueiro, 王安萍. 蜘蛛大壶状腺丝的反复拉伸力学行为和性能[J]. 材料研究学报, 2022, 36(10): 747-759.
[10] 鄢俊, 杨进, 王涛, 徐桂龙, 李朝晖. 有机硅油改性水性酚醛的制备及其性能[J]. 材料研究学报, 2021, 35(9): 651-656.
[11] 张昊, 李帆, 常娜, 王海涛, 程博闻, 王攀磊. 羧酸型接枝淀粉吸附树脂的制备和对染料的去除性能[J]. 材料研究学报, 2021, 35(6): 419-432.
[12] 孙丽颖, 钱建华, 赵永芳. AgNWs-TPU/PVDF柔性薄膜电容传感器的制备和性能[J]. 材料研究学报, 2021, 35(6): 441-448.
[13] 唐开元, 黄洋, 黄湘舟, 葛颖, 李娉婷, 袁凡舒, 张威威, 孙东平. 碳化细菌纤维素的理化性质及其在甲醇电催化中的应用[J]. 材料研究学报, 2021, 35(4): 259-270.
[14] 苏晨文, 张婷玥, 郭丽伟, 李乐, 杨苹, 刘艳秋. 用于模拟细胞外基质的硫醇-烯水凝胶的制备[J]. 材料研究学报, 2021, 35(12): 903-910.
[15] 徐春萍, 陈春悦, 张永航, 龚维, 班大明. 含磷聚合物型阻燃剂(PMP)对乙烯基酯树脂(VER)的阻燃改性[J]. 材料研究学报, 2021, 35(11): 843-849.