Please wait a minute...
材料研究学报  2010, Vol. 24 Issue (2): 175-181    
  研究论文 本期目录 | 过刊浏览 |
低碳钢在Ae3以上形变诱导铁素体的形成和性能
郝露菡; 肖纳敏; 郑成武; 李殿中
中科院金属所沈阳材料科学国家(联合)实验室 沈阳 110016
The Formation and Mechanical Properties of Deformation Induced Ferrite above Ae3 Temperature
HAO Luhan; XIAO Namin; ZHENG Chengwu; LI Dianzhong
Shenyang National Laboratory for Materials Science; Institute of Metal Research; Chinese Academy of Sciences; Shenyang 110016
引用本文:

郝露菡 肖纳敏 郑成武 李殿中. 低碳钢在Ae3以上形变诱导铁素体的形成和性能[J]. 材料研究学报, 2010, 24(2): 175-181.
, , , . The Formation and Mechanical Properties of Deformation Induced Ferrite above Ae3 Temperature[J]. Chin J Mater Res, 2010, 24(2): 175-181.

全文: PDF(972 KB)  
摘要: 

对低碳钢在Ae3以上进行了单道次快速大形变量变形, 测定了材料在高温变形前后的室温拉伸曲线并观察其断口形貌。对结果的分析表明, 低碳钢在Ae3以上的温度发生形变诱导铁素体相变, 是形成超细晶粒(3 μm左右)的主要原因。应变速率大于0.1 s-1时, 可诱导形成铁素体晶粒, 且随着应变速率的提高铁素体分数增加而晶粒尺寸减小; 当应变速率大于10 s-1时铁素体分数达到饱和, 晶粒尺寸的变化不大。与先共析铁素体相比, 形变诱导铁素体的强度和硬度大大提高, 低碳钢Q235的屈服强度由250 MPa左右提高到510 MPa, 抗拉强度则达到615 MPa, 而形变诱导铁素体的塑性有所降低, 但仍保持较高的水平。

关键词 金属材料  拉伸力学性能   形变诱导铁素体  应变速率  低碳钢    
Abstract

A series of tests of fast-single pass-heavy deformation in low carbon steel was carried out using Gleeble 3500 thermal-mechanical simulation machine at the temperature above Ae3. The mechanical property of material before and after deformation was tested, and the fracture morphology was observed. Results denote that the deformation induced ferrite transformation (DIFT) above Ae3 is responsible for the ultra-fine grain size (about 3 μm). DIF can be induced when strain rate was 0.1 s−1. With the raise of strain rate, ferrite fraction becomes larger and the grain size smaller until DIF is saturated at the strain rate of 10 s−1. Grain refinement through DIFT leads to an increase in strength and hardness. For low carbon steel Q235, the yield strength can be improved from 250 MPa to 510 MPa and the tensile strength arrives at 625 MPa, and the plasticity decreases slightly which will remains in high level.

Key wordsmetallic materials     tension mechanical properties    deformation induced ferrite transformation    stain rate    low carbon steel
收稿日期: 2009-07-13     
基金资助:

国家自然科学基金50871109资助项目。

1 Z.M.Yang, R.Z.Wang, Formation of ultra-Fine grain structure of plain low carbon steel through deformation induced ferrite transformation, ISIJ International, 43(5), 761(2003)
2 C.M.Li, H.Yada, H.Yamagata, An in situ X-ray diffraction study of γ → α transformation during hot deformation in Fe-mass%Ni-0.0008-0.29mass%C alloys, ISIJ International, 39(2), 209(1999)
3 M.R.Hickson, R.K.Gibbs, P.D.Hodgson, The effect of chemistry on the formation of ultrafine ferrite in steel, ISIJ International, 39(11),1176(1999)
4 P.D.Hodgson, M.R.Hickson, R.K.Gibbs, Ultrafine ferrite in low carbon steel, Scripta Materialia, 40(10), 1179(1999)
5 LIU Zhaoxia, LI Dianzhong, QIAO Guiwen, Investigation on deformation induced ferrite (a kind of martensite) transformation above Ae3 temperature in a low carbon steel, Acta Metallurgica Sinica, 41(11), 1127(2005)
(刘朝霞, 李殿中, 乔桂文, 低碳钢在Ae3温度之上的形变诱导铁素体(一种马氏体)的相变研究, 金属学报, 41(11), 1127(2005))
6 R.Priestner, A.K.Ibraheem, Processing of steel for ultrafine ferrite grain structures, Materials Science and Technology, 16(11-12), 1267(2000)
7 YANG Zhongmin, ZHAO Yan, WANG Ruizhen, MA Yanwen, CHE Yanmin, Formation mechanism of deformation induced ferrite, Acta Metallurgica Sinica, 36(8),818(2000)
(杨忠民, 赵 燕, 王瑞珍, 马燕文, 车彦民, 形变诱导铁素体的形成机制, 金属学报,   36(8), 818(2000))
8 YANG Zhongmin, ZHAO Yan, WANG Ruizhen, CHE Yanmin, MA Yanwen, Formation of ultra-fine ferrite grains in low carbon steels through low temperature heavy deformation, Acta Metallurgica Sinica, 36(10), 1061(2000)
(杨忠民, 赵 燕, 王瑞珍, 车彦民, 马燕文, 低温变形低碳钢超细铁素体的形成, 金属学报,  36(10), 1061(2000))
9 ZHAO Heshan, LI Dianzhong, LIU Zhaoxia, LI Yiyi, Investigation on diffusion of carbon atoms and stability of deformation induced ferrite in a low carbon steel, Acta Metallurgica Sinica, 43(3), 286(2007)
(赵河山, 李殿中, 刘朝霞, 李依依, 低碳钢形变诱导铁素体相中碳原子的扩散与稳定性研究, 金属学报,  43(3),286(2007))
10 YANG Ping, FU Yunyi, CUI Fenge, SUN Zuqing, Influence of deforming temperatures on the strain induced transformation in Q235 plain carbon steel, Acta Metallurgica Sinica, 37(6), 601(2001)
(杨 平, 傅云义, 崔凤娥, 孙祖庆, 形变温度对Q235碳素钢应变诱导相变的影响, 金属学报, 37(6), 601(2001))
11 LIU Zhaoxia, Investigation on the high temperature deformation induced ferrite transformation in a low carbon steel, PhD thesis, Institute of Metal research(2007)
(刘朝霞, 低碳钢高温形变诱导铁素体相变机理研究, 博士学位论文, 中科院金属所(2007))
12 WENG Yuqing, Ultrafine Grained Steels-The Fine Structure Theory and Control Technology (Beijing, Metallurgical Industry Press, 2003) p.63,123
(翁宇庆,  超细晶钢-钢的组织细化理论与控制技术 (北京, 冶金工业出版社,2003) p.63,123)
13 QI Junjie, YANG Wenyue, SUN Zuqing, Ultra-fine ferrite formation during deformation of undercooled austenite in a low carbon steel, Acta Metallurgica Sinica, 38(9), 897(2002)
(齐俊杰, 杨玥王 ,孙祖庆, 低碳钢过冷奥氏体形变过程超细铁素体的形成, 金属学报,  38(9), 897(2002))
14 W.B.Morrison, R.L.Miller, in: Ultrafine-grain Metals, The ductility of ultrafine grained alloys, edited by J.J.Burke, V.Weiss (New York, Syracuse University Press, 1970) p.183
15 P.D.Hodgson, R.K.Gibbs, A mathematical model to predict the mechanical properties of hot rolled C-Mn and microalloyed steels, ISIJ International, 32(12), 1329(1992)
16 R.Song, D.Ponge, D.Raabe, Improvement of the work hardening rate of ultrafine grained steels through second phase particles, Scripta Materialia, 52(11),1075(2005)
17 A.Ohmori, S.Torizuka, K.Nagai, Strain-hardening due to dispersed cementite for low carbon ultrafine-grained steels, ISIJ International, 44(6), 1063(2004)
18 W.B.Morrison, The effect of grain size on the stress-strain relationship in low-carbon steel, Trans. ASM, 59(4),824(1966)

[1] 毛建军, 富童, 潘虎成, 滕常青, 张伟, 谢东升, 吴璐. AlNbMoZrB系难熔高熵合金的Kr离子辐照损伤行为[J]. 材料研究学报, 2023, 37(9): 641-648.
[2] 宋莉芳, 闫佳豪, 张佃康, 薛程, 夏慧芸, 牛艳辉. 碱金属掺杂MIL125CO2 吸附性能[J]. 材料研究学报, 2023, 37(9): 649-654.
[3] 赵政翔, 廖露海, 徐芳泓, 张威, 李静媛. 超级奥氏体不锈钢24Cr-22Ni-7Mo-0.4N的热变形行为及其组织演变[J]. 材料研究学报, 2023, 37(9): 655-667.
[4] 邵鸿媚, 崔勇, 徐文迪, 张伟, 申晓毅, 翟玉春. 空心球形AlOOH的无模板水热制备和吸附性能[J]. 材料研究学报, 2023, 37(9): 675-684.
[5] 幸定琴, 涂坚, 罗森, 周志明. C含量对VCoNi中熵合金微观组织和性能的影响[J]. 材料研究学报, 2023, 37(9): 685-696.
[6] 欧阳康昕, 周达, 杨宇帆, 张磊. LPSOMg-Y-Er-Ni合金的组织和拉伸性能[J]. 材料研究学报, 2023, 37(9): 697-705.
[7] 徐利君, 郑策, 冯小辉, 黄秋燕, 李应举, 杨院生. 定向再结晶对热轧态Cu71Al18Mn11合金的组织和超弹性性能的影响[J]. 材料研究学报, 2023, 37(8): 571-580.
[8] 熊诗琪, 刘恩泽, 谭政, 宁礼奎, 佟健, 郑志, 李海英. 固溶处理对一种低偏析高温合金组织的影响[J]. 材料研究学报, 2023, 37(8): 603-613.
[9] 刘继浩, 迟宏宵, 武会宾, 马党参, 周健, 徐辉霞. 喷射成形M3高速钢热处理过程中组织的演变和硬度偏低问题[J]. 材料研究学报, 2023, 37(8): 625-632.
[10] 由宝栋, 朱明伟, 杨鹏举, 何杰. 合金相分离制备多孔金属材料的研究进展[J]. 材料研究学报, 2023, 37(8): 561-570.
[11] 任富彦, 欧阳二明. g-C3N4 改性Bi2O3 对盐酸四环素的光催化降解[J]. 材料研究学报, 2023, 37(8): 633-640.
[12] 王昊, 崔君军, 赵明久. 镍基高温合金GH3536带箔材的再结晶与晶粒长大行为[J]. 材料研究学报, 2023, 37(7): 535-542.
[13] 刘明珠, 樊娆, 张萧宇, 马泽元, 梁城洋, 曹颖, 耿仕通, 李玲. SnO2 作散射层的光阳极膜厚对量子点染料敏化太阳能电池光电性能的影响[J]. 材料研究学报, 2023, 37(7): 554-560.
[14] 秦鹤勇, 李振团, 赵光普, 张文云, 张晓敏. 固溶温度对GH4742合金力学性能及γ' 相的影响[J]. 材料研究学报, 2023, 37(7): 502-510.
[15] 刘天福, 张滨, 张均锋, 徐强, 宋竹满, 张广平. 缺口应力集中系数对TC4 ELI合金低周疲劳性能的影响[J]. 材料研究学报, 2023, 37(7): 511-522.