Please wait a minute...
材料研究学报  2012, Vol. 26 Issue (5): 538-544    
  研究论文 本期目录 | 过刊浏览 |
Al2O3/TiC--Al2O3/TiC/CaF2自润滑叠层陶瓷的机械和摩擦磨损性能
宋培龙, 杨学锋, 王守仁, 杨丽颖
济南大学机械工程学院 济南 250022
Mechanical and Tribological Properties of Laminated Al2O3/TiC–Al2O3/TiC/CaF2 Self-lubrication Ceramic Material
SONG Peilong, YANG Xuefeng, WANG Shouren, YANG Liying
School of Mechanical Engineering, University of Jinan, Jinan 250022
引用本文:

宋培龙 杨学锋 王守仁 杨丽颖. Al2O3/TiC--Al2O3/TiC/CaF2自润滑叠层陶瓷的机械和摩擦磨损性能[J]. 材料研究学报, 2012, 26(5): 538-544.
SONG Peilong YANG Xuefeng WANG Shouren YANG Liying. Mechanical and Tribological Properties of Laminated Al2O3/TiC–Al2O3/TiC/CaF2 Self-lubrication Ceramic Material[J]. Chinese Journal of Materials Research, 2012, 26(5): 538-544.

全文: PDF(1124 KB)  
摘要: 

采用真空热压烧结制备了Al2O3/TiC--Al2O3/TiC/CaF2自润滑叠层陶瓷材料, 其平均维氏硬度为20.7GPa, 断裂韧性为4.5 MPa•m1/2, 在垂直于叠层方向和平行于叠层方向上的抗弯强度差别不大, 分别为323 MPa和353 MPa。在环盘式摩擦磨损试验机上进行摩擦磨损实验, 研究了该材料在干摩擦条件下与淬火45#钢配副时的摩擦磨损规律。用扫描电镜(SEM)及能量弥散X射线谱(EDS)观察了材料磨损前后的微观形貌并分析其成分组成及其磨损机理。结果表明: Al2O3/TiC--Al2O3/TiC/CaF2自润滑叠层陶瓷材料磨擦系数和磨损率均随着转速和载荷的升高而下降;具有自润滑特性;Al2O3/TiC--Al2O3/TiC/CaF2复合叠层陶瓷材料的磨损机理主要是磨粒磨损和黏着磨损。

关键词 复合材料叠层陶瓷材料自润滑摩擦磨损    
Abstract

Al2O3/TiC–Al2O3/TiC/CaF2 laminated composite ceramic material was prepared by vacuum hot pressing sintering. The Vickers hardness is 20.7 GPa and the fracture toughness is 4.5 MPa·m1/2. The bending strength has little difference in the vertical direction and parallel direction which is respectively for 323 MPa and 353 MPa. Sliding wear tests against chilled 45# steel were performed on the ceramic composites using ring-disc method in dry conditions, worn morphology was observed by the scanning electron microscope (SEM) and the composition was investigated by energydispersive X-Ray spectroscopy (EDS). Results show that the friction coefficient and wear rate decline with the increase of the load and rotating speed. The material has self-lubricated property. The main wear mechanisms of laminated composite are abrasive wear and adhesive wear.

Key wordscomposites    laminated ceramic materials    self-lubrication    wear and friction
收稿日期: 2012-08-13     
ZTFLH:  TH145  
基金资助:

国家自然科学基金青年科学基金项目51005100、中国博士后科学基金面上项目20110491572和山东省科技发展计划2012GGX10324资助。


1 WEI Jianjun, XUE Qunji, The situation of the tribological research for ceramics, Tribology, 13(3), 268(1993)

(魏建军, 薛群基, 陶瓷摩擦学研究的发展现状, 摩擦学学报,  13(3), 268(1993))

2 ZAN Qingfeng, CAI Shengyou, HUANG Yong, The influence of the toughness on the component of soft-layer in the Si3N4/BN multilayered materials, Shandong Ceramic, 22(2), 4(1999)

(昝青峰, 蔡胜有, 黄  勇, Si3N4/BN层状陶瓷软层成分对材料韧性的影响, 山东陶瓷,  22(2), 4(1999))

3 N.Liu, M.Shi, Y.D.Xu, X.Q.You, P.P.Ren, J.P.Feng, Effect of starting powders size on the Al2O3-TiC composites, International Journal of Refractory Metals & Hard Materials, 22, 265(2004)

4 Q.Tai, A.Mocellin, Review: High temperature deformation of Al2O3 based ceramic particle or whisker composites, Ceramics International, 25, 395(1999)

5 Yongsheng ZHANG, Litian HU, Jianmin CHEN, Weimin LIU, Lubrication behavior of Y-TZP/Al2O3/Mo nanocomposites at high temperature, Wear, 268, 1091(2010)

6 CHENG Yin, XIAO Hanning, LI Yuping, Reinforcement mechanisms and preparation of laminated ceramic composites, Journal of Ceramic, 24(2), 111(2003)

(成 茵, 肖汉宁, 李玉平, 层状复合陶瓷增韧机理和制备工艺的研究, 陶瓷学报,  24(2), 111(2003))

7 LI Dongyun, QIAO Guanjun, JIN Zhihao, Progress in research on laminated ceramic composites, Journal of Inorganic Materials, 17(1), 10(2002)

(李冬云, 乔冠军, 金志浩, 层状复合陶瓷材料的研究进展, 无机材料学报,  17(1), 10(2002))

8 ZENG Yuping, JIANG Dongliang, TAN Shouhong, GUO Jingkun, Fabrication and properties of multilayer al2o3-tic composite ceramic, Journal of Inorganic Materials, 12(6), 802(1997)

(曾宇平, 江东亮, 谭寿洪, 郭景坤, 层状Al2O3-TiC复相陶瓷的制备与性能, 无极材料学报,  12(6), 802(1997))

9 CHEN Bei, DING Peidao, CHENG Chuan, Relationship between processing and mechanical property of A12O3/ZrO2 laminated ceramics, Bulletin of the Chinese Ceramic Society, 6, 27(2004)

(陈 蓓, 丁培道, 程 川, 层状复合陶瓷材料制备工艺与性能关系, 硅酸盐通报,  6, 27(2004))

10 LI Xiuhua, YUAN Qiming, YANG Zhengfang, The conch structure and biomimetic research on ceramics, Bulletin of the Chinese Ceramic Society, 2, 53(2003)

(李秀华, 袁启明, 杨正方, 贝壳结构及陶瓷的仿生研究, 硅酸盐通报,  2, 53(2003))

11 QIAN Xiaoqian, GE Manzhen, WU Yibing, YANG Hui, Reinforcement mechanisms and optimum design of laminated ceramic composites, Journal of Inorganic Materials, 14(4), 520(1999)

(钱晓倩, 葛曼珍, 吴义兵, 杨 辉, 层状复合陶瓷强韧化机制及其优化设计因素, 无机材料学报,  14(4), 520(1999))

12 W.J.Clegg, K.Kendall, N.M.Alford, A simple way to make tough ceramics, Nature, 347(10), 445(1990)

13 Henryk, Tomaszewski, Residual stress in layered ceramic composites, Journal of the European Ceramic Society, 19, 1329(1999)

14 YU Haijiang, WAN Julin, LIANG Kaiming, WANG Daning, LIU Fengru, 14% mol Ce-TZP and A12O3/Ce-TZP layered microcomposites, Journal of Inorganic Materials, 13(6), 893(1998)

(俞海江, 万菊林, 梁开明, 王大宁, 刘凤茹, 14mol%Ce--TZP和Al2O3/Ce--TZP层状复合材料的研究, 无机材料学报,  13(6), 893(1998))

15 Robert J. Moon, Mark Hoffman, Jon Hilden, Weight function analysis on the R-curve behavior of multilayered alumina-zirconia composite, Journal of the American Chemical Society, 85(6),1505(2002)

16 DING Xingeng, GE Manzhen, YANG Hui, Preparation and properties of laminated Al2O3/ZTA, Bulletin of the Chinese Ceramic Society, 19, 50(2000)

(丁新更, 葛曼珍, 杨 辉, 氧化铝/ZTA强夹层层状复合陶瓷的制备和性能, 硅酸盐通报,  19, 50(2000))

17 Hailong Wan, Bingbing Fan, Lun Feng, Deliang Chen, Hongxia Lu, Hongliang Xu, Chang-An Wang, Rui Zhang, The fabrication and mechanical properties of SiC/ZrB2 laminated ceramic composite prepared by spark plasma sintering, Ceramics International, 6(38),5015(2012)

18 Dongyun Li, Guanjun Qiao, Zhihao Jin, R-curve behavior of laminated SiC/BN ceramics, Ceramics International, 2(30), 213(2004)

19 CAI Shengyou, LI Jinlin, XIE Zhipeng, HUANG Yong, Influence of interfacial bonding of Si3N4 laminated composites on the mechanical properties, Acta Materiae Compositae

Sinica, 16(2), 110(1999)

(蔡胜有, 李金林, 谢志鹏, 黄 勇, 氮化硅层状陶瓷界面性能对力学性能的影响, 复合材料学报,  16(2), 110(1999))

20 V.Yaroshenko, Nina Orlovskaya, M.A.Einarsrud, Karl Berroth, V.Kovylayev, Laminar Si3N4-TiN hot-pressed ceramic composites, Key Engineering Materials, 132-136, 2017(1997)

21 XUE Qunji, LU Jinjun, Research status and developing trend of solid lubrication at high temperatures, Tribology, 19(1), 91(1999)

(薛群基, 吕晋军, 高温固体润滑研究的现状及发展趋势, 摩擦学学报,  19(1), 91(1999))

22 YANG Xuefeng, ZE Xiangbo, Wang Hongyan, Wear properties and microstructures of alumina matrix composite ceramics used for drawing dies, Ceramics International, 34(12), 3495(2009)

23 Tingzhi Si, Ning Liu, Qing’an Zhang, Xianqing You, Thermal shock fatigue behavior of TiC/Al2O3 composite ceramics, Rare Metals, 3(27), 308(2008)

24 CAO Tongkun, GAO Wei, Wear behavior and mechanism of self tribofilm formation of Al2O3/TiC/CaF2, Journal of Materials Engineering, 9,75(2009)

(曹同坤, 高 伟, Al2O3/TiC/CaF2陶瓷的摩擦磨损及自润滑膜的形成机理研究, 材料工程, 9,75(2009))

25 CAO Tongkun, DENG Jianxin, Friction and wear behavior of self-lubricating ceramic composite, Tribology, 25(6), 564(2005)

(曹同坤, 邓建新, 一种自润滑陶瓷摩擦磨损性能的研究, 摩擦学学报,  25(6), 564(2005))


[1] 幸定琴, 涂坚, 罗森, 周志明. C含量对VCoNi中熵合金微观组织和性能的影响[J]. 材料研究学报, 2023, 37(9): 685-696.
[2] 潘新元, 蒋津, 任云飞, 刘莉, 李景辉, 张明亚. 热挤压钛/钢复合管的微观组织和性能[J]. 材料研究学报, 2023, 37(9): 713-720.
[3] 刘瑞峰, 仙运昌, 赵瑞, 周印梅, 王文先. 钛合金/不锈钢复合板的放电等离子烧结技术制备及其性能[J]. 材料研究学报, 2023, 37(8): 581-589.
[4] 季雨辰, 刘树和, 张天宇, 查成. MXene在锂硫电池中应用的研究进展[J]. 材料研究学报, 2023, 37(7): 481-494.
[5] 王伟, 解泽磊, 屈怡珅, 常文娟, 彭怡晴, 金杰, 王快社. Graphene/SiO2 纳米复合材料作为水基润滑添加剂的摩擦学性能[J]. 材料研究学报, 2023, 37(7): 543-553.
[6] 张藤心, 王函, 郝亚斌, 张建岗, 孙新阳, 曾尤. 基于界面氢键结构的石墨烯/聚合物复合材料的阻尼性能[J]. 材料研究学报, 2023, 37(6): 401-407.
[7] 邵萌萌, 陈招科, 熊翔, 曾毅, 王铎, 王徐辉. C/C-ZrC-SiC复合材料的Si2+ 离子辐照行为[J]. 材料研究学报, 2023, 37(6): 472-480.
[8] 张锦中, 刘晓云, 杨健茂, 周剑锋, 查刘生. 温度响应性双面纳米纤维的制备和性能[J]. 材料研究学报, 2023, 37(4): 248-256.
[9] 王刚, 杜雷雷, 缪自强, 钱凯成, 杜向博文, 邓泽婷, 李仁宏. 聚多巴胺改性碳纤维增强尼龙6复合材料的界面性能[J]. 材料研究学报, 2023, 37(3): 203-210.
[10] 林师峰, 徐东安, 庄艳歆, 张海峰, 朱正旺. TiZr基非晶/TC21双层复合材料的制备和力学性能[J]. 材料研究学报, 2023, 37(3): 193-202.
[11] 苗琪, 左孝青, 周芸, 王应武, 郭路, 王坦, 黄蓓. 304不锈钢纤维/ZL104铝合金复合泡沫的孔结构、力学、吸声性能及其机理[J]. 材料研究学报, 2023, 37(3): 175-183.
[12] 张开银, 王秋玲, 向军. FeCo/SnO2 复合纳米纤维的制备及其吸波性能[J]. 材料研究学报, 2023, 37(2): 102-110.
[13] 周聪, 昝宇宁, 王东, 王全兆, 肖伯律, 马宗义. (Al11La3+Al2O3)/Al复合材料的高温性能及其强化机制[J]. 材料研究学报, 2023, 37(2): 81-88.
[14] 罗昱, 陈秋云, 薛丽红, 张五星, 严有为. 钠离子电池双层碳包覆Na3V2(PO4)3 正极材料的超声辅助溶液燃烧合成及其电化学性能[J]. 材料研究学报, 2023, 37(2): 129-135.
[15] 刘志华, 岳远超, 丘一帆, 卜湘, 阳涛. g-C3N4/Ag/BiOBr复合材料的制备及其光催化还原硝酸盐氮[J]. 材料研究学报, 2023, 37(10): 781-790.