AZ31镁合金的变形织构和协调变形机理

材料研究学报

2012, Vol. 26

Issue (3): 231-239

研究论文

本期目录 | 过刊浏览

AZ31镁合金的变形织构和协调变形机理

刘华强, 唐荻, 蔡庆伍, 孟强

北京科技大学高效轧制国家工程研究中心北京 100083

Deforming Texture and Deformation Mechanism of Coordination of AZ31 Magnesium Alloy Sheets

LIU Huaqiang, TANG Di, CAI Qingwu, MENG Qiang

National Engineering Research Center of Advance Rolling Technology, University of Science and Technology Beijing, Beijing 100083

引用本文:

刘华强唐荻蔡庆伍孟强. AZ31镁合金的变形织构和协调变形机理[J]. 材料研究学报, 2012, 26(3): 231-239.
, . Deforming Texture and Deformation Mechanism of Coordination of AZ31 Magnesium Alloy Sheets[J]. Chin J Mater Res, 2012, 26(3): 231-239.

全文: PDF(0 KB)

摘要: 进行变形速率可控的单向拉伸试验, 研究了变形织构与滑移和孪生等协调变形机理对AZ31镁合金综合性能的影响。结果表明: 在沿挤压方向拉伸过程中, 变形织构使{0002}晶面Schmid因子较低, 基面滑移难以开动, 屈服强度高。在沿45^o拉伸过程中, 变形织构使柱面取向晶粒处于发生{0002}滑移的最佳位置, 基面取向晶粒的棱柱面滑移也处于最佳位置, 屈服强度低而延伸率高。沿横向拉伸的力学性能主要受孪晶影响, 由于大量孪晶诱发裂纹, 延伸率最低。试样在45^o和横向拉伸时产生的大量拉伸孪晶, 是出现{0002}双峰织构的诱因。

关键词 ：金属材料, 变形镁合金, 织构, 滑移, 孪生, 变形机理

Abstract：The effects of deforming texture and deformation mechanisms of slip and twinning on the comprehensive performance of AZ31 magnesium alloy sheets were investigated by using uniaxial tensile test with controlled strain rate. The results show that the Schmid factor of {0002} basal plane is low, the slip of basal plane is difficult to start, and the yield strength is bigger along the tensile direction of extrusion. The grains of prismatic orientation lie in the best position for {0002} plane slipping, and the prismatic slip of the basal plane orientation also is in the best position. Therefore, the yield strength is low, and the elongation is bigger along the tensile direction of 45^o. The twins have an important effect on the mechanical properties of the sheets, and the elongation is lower because the large numbers of twins induce crack along the transverse tensile direction. The large numbers of tensile twins are the inducement of producing the double peak texture of {0002} palne along the tensile direction of 45^o and transverse direction.

Key words： metallic materials wrought magnesium alloy texture slip twins deformation mechanism

收稿日期: 2011-12-26

ZTFLH:

TG146

基金资助:

国家十二五镁合金支撑基金2011BAE22B00和中央高校基本科研业务费专项基金资助项目。

	服务

	把本文推荐给朋友
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	刘华强
	唐荻
44.8K

链接本文:

https://www.cjmr.org/CN/ 或 https://www.cjmr.org/CN/Y2012/V26/I3/231

1 CHEN Zhenhua, Wrought Magnesium Alloys (Beijing, Chemical Industry Press, 2005) p.35-36

(陈振华主编, 变形镁合金 (北京, 化学工业出版社, 2005) p.35-36)

2 YU Kun, LI Wenxian, WANG Richu, MA Zhengqing, Research, development and application of wrought magnesium alloys, The Chinese Journal of Nonferrous Metals, 13(2), 277(2003)

(余琨, 黎文献, 王日初, 马正清, 变形镁合金的研究、开发及应用, 中国有色金属学报, 13(2), 277(2003))

3 S.B.Yi, H.G.Brokmeier, D.Letziga, Microstructure evolution during the annealing of an extruded AZ31 magnesium alloy, Journal of Alloys and Compounds, 506(1), 364(2010)

4 L.Guan, G.Y.Tang, Y.B.Jiang, Texture evolution in coldrolled AZ31 magnesium alloy during electro pulsing treatment, Journal of Alloys and Compounds, 487(1–2), 309(2009)

5 YANG Xuyue, ZHU Yakun, ZHANG Lei, Quantitative studies of the microstructure of hot deformed magnesium alloy, Chinese journal of materials research, 24(2), 169(2010)

(杨续跃, 朱亚坤, 张雷, 热变形镁合金退火显微组织的定量研究, 材料研究学报, 24(2), 169(2010))

6 QU Jia, ZHANG Zhenggui, WANG Fu, ZUO Liang, Evolution of texture of the AZ31 magnesium alloy by the cross shear rolling at room temperature, Chinese journal of materials

research, 21(4), 354(2007)

(曲家, 张正贵, 王福, 左良, AZ31镁合金室温异步轧制的织构演变, 材料研究学报, 21(4), 354(2007))

7 X.P.Chen, D.Shang, R.Xiao, Influence of rolling ways on microstructure and anisotropy of AZ31 alloy sheet, Transactions of Nonferrous Metals Society of China, 20(2), 589(2010)

8 WANG Lingyun, FAN Yongge, HANG Guangjie, HUANG Guangsheng, PAN Fusheng, LIU Zhenghong, Texture of AZ31B magnesium alloy sheets, Chinese Journal of Materials

Research, 18(5), 466(2004)

(汪凌云, 范永革, 黄光杰, 黄光胜, 潘复生, 刘正宏, AZ31B镁合金板材的织构, 材料研究学报, 18(5), 466(2004))

9 WANG Lina, YANG Ping, CHEN Zhenhua, XIA Weijun, CHEN Ding, LI Xiao, MENG Li, Textures and deformation mechanisms of AZ31 magnesium alloys under special processing technologies, Acta Metall Sin, 45(1), 58(2009)

(王丽娜, 杨平, 陈振华, 夏伟军, 陈鼎, 李萧, 孟利, 特殊成形工艺下AZ31镁合金的织构及变形机制, 金属学报, 45(1), 58(2009)

10 K.Yu, S.T.Rui, X.Y.Wang, Texture evolution of extruded AZ31 magnesium alloy sheets, Transactions of Nonferrous Metals Society of China, 19(3), 511(2009)

11 B.Beausir, S.Suwas, L.Toth, Analysis of texture evolution in magnesium during equal channel angular extrusion, Acta Materialia, 56(2), 200(2008)

12 YANG Ping, HU Yisong, CUI Feng’e, Texture investigation on the deformation mechanisms magnesium alloy AZ31 deformed at high temperature, Chinese Journal of Materials Research, 18(1), 52(2004)

(杨平, 胡轶篙, 崔凤娥, 镁合金AZ31高温形变机制的织构分析, 材料研究学报, 18(1), 52(2004))

13 J.Bohlen, S.B.Yi, J.Swiostek, Microstructure and texture development during hydrostatic extrusion of magnesium alloy AZ31, Scripta Materialia, 53(2), 259(2005)

14 M.D.Nave, M.R.Barnett, Microstructures and textures of pure magnesium deformed in plane-strain compression, Scripta Materialia, 51(9), 881(2004)

15 L.Helis, K.Okayasu, H.Fukutomi, Microstructure evolution and texture development during high-temperature uniaxial compression of magnesium alloy AZ31, Materials Science and Engineering A, 430(1–2), 98(2006)

16 MENG Li, An EBSD micro-texture study on hot and warm deformation behaviors of magnesium alloys, Ph.D thesis, University of Science and Technology Beijing, 54(2008)

(孟利, 镁合金热、温形变行为的EBSD微织构研究, 博士学位论文, 北京科技大学, 54(2008))

17 M.R.Barnett, Twinning and the ductility of magnesium alloys, Materials Science and Engineering A, 464(1–2), 1(2007)

18 C.Roucoules, M.Pietrzyk, P.D.Hodgson, Analysis of work hardening and recrystallization during the hot working of steel using a statistically based internal variable model, Materials Science and Engineering A, 339(1–2), 1(2003)

19 J.Koike, T.Kobayashi, T.Mukai, The activity of non-basal slip systems and dynamic recovery at room temperature in fine-grained AZ31Bmagnesium, Acta Materialia, 51(7), 2055(2003)

20 J.W.Christian, S.Mahajan, Deformation twinning, Progress in Materials Science, 39(1–2), 1(1995)

21 N.Munroe, X.L.Tan, H.C.Gu, Orientation dependence of slip and twinning in hcp metals, Scripta Mater, 36(12), 1383(1997)

22 A.Styczynski, C.Hartig, J.Bohlen, Cold rolling textures in AZ31 wrought magnesium alloy, Scripta Mater, 50(7), 943(2004)

23 S.R.Agnew, M.H.Yoo, C.N.Tome, Application of texture simulation to understanding mechanical behavior of Mg and solid solution alloys containing Li or Y, Acta Materialia, 49(20), 4277(2001)

24 P.Yang, Y.Yu, L.Chen, Experimental determination and theoretical prediction of twin orientations in magnesium alloy AZ31, Scripta Materialia, 50(8), 1163(2004)

[1]	毛建军, 富童, 潘虎成, 滕常青, 张伟, 谢东升, 吴璐. AlNbMoZrB系难熔高熵合金的Kr离子辐照损伤行为[J]. 材料研究学报, 2023, 37(9): 641-648.
[2]	宋莉芳, 闫佳豪, 张佃康, 薛程, 夏慧芸, 牛艳辉. 碱金属掺杂MIL125的CO₂ 吸附性能[J]. 材料研究学报, 2023, 37(9): 649-654.
[3]	赵政翔, 廖露海, 徐芳泓, 张威, 李静媛. 超级奥氏体不锈钢24Cr-22Ni-7Mo-0.4N的热变形行为及其组织演变[J]. 材料研究学报, 2023, 37(9): 655-667.
[4]	邵鸿媚, 崔勇, 徐文迪, 张伟, 申晓毅, 翟玉春. 空心球形AlOOH的无模板水热制备和吸附性能[J]. 材料研究学报, 2023, 37(9): 675-684.
[5]	幸定琴, 涂坚, 罗森, 周志明. C含量对VCoNi中熵合金微观组织和性能的影响[J]. 材料研究学报, 2023, 37(9): 685-696.
[6]	欧阳康昕, 周达, 杨宇帆, 张磊. 含LPSO相Mg-Y-Er-Ni合金的组织和拉伸性能[J]. 材料研究学报, 2023, 37(9): 697-705.
[7]	徐利君, 郑策, 冯小辉, 黄秋燕, 李应举, 杨院生. 定向再结晶对热轧态Cu71Al18Mn11合金的组织和超弹性性能的影响[J]. 材料研究学报, 2023, 37(8): 571-580.
[8]	熊诗琪, 刘恩泽, 谭政, 宁礼奎, 佟健, 郑志, 李海英. 固溶处理对一种低偏析高温合金组织的影响[J]. 材料研究学报, 2023, 37(8): 603-613.
[9]	刘继浩, 迟宏宵, 武会宾, 马党参, 周健, 徐辉霞. 喷射成形M3高速钢热处理过程中组织的演变和硬度偏低问题[J]. 材料研究学报, 2023, 37(8): 625-632.
[10]	由宝栋, 朱明伟, 杨鹏举, 何杰. 合金相分离制备多孔金属材料的研究进展[J]. 材料研究学报, 2023, 37(8): 561-570.
[11]	任富彦, 欧阳二明. g-C₃N₄ 改性Bi₂O₃ 对盐酸四环素的光催化降解[J]. 材料研究学报, 2023, 37(8): 633-640.
[12]	王昊, 崔君军, 赵明久. 镍基高温合金GH3536带箔材的再结晶与晶粒长大行为[J]. 材料研究学报, 2023, 37(7): 535-542.
[13]	刘明珠, 樊娆, 张萧宇, 马泽元, 梁城洋, 曹颖, 耿仕通, 李玲. SnO₂ 作散射层的光阳极膜厚对量子点染料敏化太阳能电池光电性能的影响[J]. 材料研究学报, 2023, 37(7): 554-560.
[14]	秦鹤勇, 李振团, 赵光普, 张文云, 张晓敏. 固溶温度对GH4742合金力学性能及γ' 相的影响[J]. 材料研究学报, 2023, 37(7): 502-510.
[15]	刘天福, 张滨, 张均锋, 徐强, 宋竹满, 张广平. 缺口应力集中系数对TC4 ELI合金低周疲劳性能的影响[J]. 材料研究学报, 2023, 37(7): 511-522.

Viewed

Full text

Abstract

Cited

Shared

Discussed