|
|
|
| Effect of Addition of Alloying Elements in Welding Flux on Microstructure and Toughness of Weld Seam of FV520(B) Steel |
Jihong LI( ),Juanjuan LIU,Min ZHANG,Mingzhi LIU,Jiang TANG |
| College of Materials Science and Engineering, Xi’an University of Technology, Xi’an 710048, China |
|
Cite this article:
Jihong LI,Juanjuan LIU,Min ZHANG,Mingzhi LIU,Jiang TANG. Effect of Addition of Alloying Elements in Welding Flux on Microstructure and Toughness of Weld Seam of FV520(B) Steel. Chinese Journal of Materials Research, 2015, 29(7): 549-554.
|
|
|
Abstract The influence of addition of alloying elements of medium carbon Fe-Mn and Ni in the welding flux on the microstructure and toughness of the weld seam of FV520(B) steel was investigated by means of impact test, metallographic microscope, SEM and X-ray diffractometer. The results show that the microstructure of the weld seam of FV520(B) steel mainly composed of tempered sorbite and lath martensite with some residual austenite and secondary phases. With the increasing amount of alloying elements Mn and Ni, the microstructure of weld seam became finer, and the lamellae of martensite became thinner and distributed more uniformly. The addition of allying elements into a basic flux rather than an acidic ones showed much higher effectiveness in improvement of the toughness of the weld seam. The induced Mn and Ni can enhance the austenitic amount in the weld seam, which in turn plays an important role in enhancing its toughness. Moreover, the induced Ni rather than Mn was more effective in enhancing the toughness of the weld seam.
|
|
Received: 14 August 2014
|
| Fund: *Supported by National Natural Science Foundation of China No.51274162, the Foundation of Shaanxi Educational Committee No. 14JK1539, and the Science and Technology Program of Xi’an No. CX12163. |
| 1 | J. L. Fan, X. L. Guo, C. W. Wu, Y.G. Zhao,Research on fatigue behavior evaluation and fatigue fracture mechanisms of cruciform welded joints, Materials Science and Engineering A, 528(29/30), 8417(2011) | | 2 | FAN Junling,GUO Xinglin, ZHAO Yanguang, WU Chengwei, Predictions of S-N curve and residual life of welded Joints by quantitative thermographic method, Journal of Materials Engineering, (12), 29(2011) | | 2 | (樊俊铃, 郭杏林, 赵延广, 吴承伟, 定量热像法预测焊接接头的曲线和残余寿命, 材料工程, (12), 29(2011)) | | 3 | ZHANG Yiliang,ZHU Yunqing, ZHANG Zhenhai, Blower impeller fast fracture detection and failure analysis, Journal of Safety and Environment, 7(1), 132(2007) | | 3 | (张亦良, 朱蕴卿, 张振海, 鼓风机叶轮快速断裂的检测及失效分析, 安全与环境学报, 7(1), 132(2007)) | | 4 | ZHANG Min,CHAO Lining, LI Jihong, ZHANG Meili, Failure analysis on fracture of gas blower turbine wheel, Hot Working Technology, 40(12), 190(2011) | | 4 | (张 敏, 晁利宁, 李继红, 张美丽, 某焦炉煤气风机叶轮断裂失效分析, 热加工工艺, 40(12), 190(2011)) | | 5 | ZHOU Qianqing,ZHAI Yuchun, Aging process optimization for a high strength and toughness of FV520B martensitic steel, Acta Metallurgica Sinica, 45(10), 1249(2009) | | 5 | (周倩青, 翟玉春, 高强高韧FV520B马氏体钢的时效工艺优化, 金属学报, 45(10), 1249(2009)) | | 6 | XU Zuyao,Effect of alloying elementts in specical steel heat treatment, Ordnance Material Science and Engineering, 3(1), 1(1982) | | 6 | (徐祖耀, 特殊钢热处理中合金元素的作用, 兵器材料科学与工程, 3(1), 1(1982)) | | 7 | ZHANG Futian,JIANG Jian, SONG Jianxian, HAN Ci, Study of Mossbauer spectroscopy of Ni9 steel rotary austenitic phase transformation, Acta Metallurgica Sinica, 22(4), 169(1986) | | 7 | (张弗天, 姜 健, 宋建先, 韩 慈, Ni9钢回转奥氏体相变的Mossbauer谱学研究, 金属学报, 22(4), 169(1986)) | | 8 | Zhu Dong,Wang Fuxing, Cai Qigong, Zheng MingXin, Cheng YinQuian, Effect of retained austenite on rolling element fatigue and its mechanism, Wear, 105(3), 223(1985) | | 9 | XU Zuyao,Low-carbon martensite and interlath austenite in steels, Iron & Steel, 22(3), 33(1987) | | 9 | (徐祖耀, 钢中的低碳马氏体及条间奥氏体, 钢铁, 22(3), 33(1987)) | | 10 | H. Nakagawa, T. Miyazaki,Effect of retained austenite on the microstructure and mechanical properties of martensitic precipitation hardening stainless steel, Journal of Materials Science, 34, 3901(1999) | | 11 | S. D. Antolovich, B. Singh,Study on the toughness increment associated with the austenite to martensite phase transformation in TRIP steels, Metal Trans, (8), 2135(1971) |
|
| No Suggested Reading articles found! |
|
|
Viewed |
|
|
|
Full text
|
|
|
|
|
Abstract
|
|
|
|
|
Cited |
|
|
|
|
| |
Shared |
|
|
|
|
| |
Discussed |
|
|
|
|
