|
|
Deformation Behavior of Alloy Mg–9Li–3Al–2.5Sr at Elevated Temperature |
LI Junchen1 , PENG Xiaodong1,2 , LIU Junwei1 , YANG Yan1 , ZENG Li1 |
1.College of Material Science and Engineering, Chongqing University, Chongqing 400045
2.National Engineering Research Center for Magnesium Alloys, Chongqing 400044 |
|
Cite this article:
LI Junchen PENG Xiaodong LIU Junwei YANG Yan ZENG Li. Deformation Behavior of Alloy Mg–9Li–3Al–2.5Sr at Elevated Temperature. Chin J Mater Res, 2012, 26(3): 309-314.
|
Abstract The uniaxial hot compression test with Gleeble–1500D thermal simulator had performed on Mg–9Li–3Al–2.5Sr alloy at 200–350℃ and strain rates of 0.001–1 s−1. The correlation between the flow stress and the temperature and strain rates were analyzed, the constitutive equation of the alloy at elevated temperature was established, and the hot processing map of the alloy was also calculated and investigated by observing the microstructure. The results show that the flow stress becomes higher with increase of strain rates at constant temperature, and lower with increase of deformation temperature at constant strain rate. The steady flow stress of the alloy deformed at elevated temperature can be well described by the hyperbolic sine constitutive equation. The result of hot processing map shows that the optimal hot working parameters for the alloy Mg–9Li–3Al–2.5Sr is at 260–300℃ and strain of 0.01–1 s−1, and the super–plastic deformation domain is at 340–350℃ and strain of 0.003–0.01 s−1.
|
Received: 11 April 2012
|
|
Fund: Supported by National Key Basic Research and Development Program of China No.2007CB613702. |
1 Y.W.Kim, D.H.Kim, H.L.Lee, C.P.Hong, WidmanstAtten type solidification in squeeze casting of Mg–Li–Al alloy, Scripta Materialia, 38(6), 923(1998)2 W.A.Counts, M.Friak, D.Raabe, J.Neugebauer, Using ab initio calculations in designing bcc Mg–Li alloys for ultra–lightweight applications, Acta Materialia, 57, 69(2009)3 C.W.Yang, T.S.Lui, L.H.Chen, H.E.Hang, Tensile mechanical properties and failure behaviors with the ductile to brittle transition of the α + β type Mg–Li–Al–Zn alloy, Scripta Materialia, 61, 1141(2009)4 H.Y.Wu, Z.W.Gao, J.Y.Lin, C.H.Chiu, Effects of minor scandium addition on the properties of Mg–Li–Al alloy, Journal of Alloys and Compounds, 474, 158(2009)5 T.Liu, S.D.Wu, S.X.Li, P.J.Li, Microstructure evolution of Mg–14%Li–1%Al alloy during the process of equal channel angular pressing, Materials Science and EngineeringA, 460, 499(2007)6 Y.Z.Lv, X.Yan, D.X.Cao, The electrochemical behaviors of Mg, Mg–Li–Al–Ce and Mg–Li–Al–Ce–Y in sodium chloride solution, Journal of Power Sources, 196, 8809(2011)7 Y.Yang, X.P.Peng, Q.Y.Wei, W.D.Xie, Z.H.Su, Influence of Sr on microstructure and mechanical properties of Mg–9Li–3Al alloy, ICMAT & IUMRS–ICA 20098 ZHOU Wei, PENG Xiaodong, YANG Yan, LIU Huatang, Influence of Sr on microstructures and high temperature mechanical properties of Mg–9Li–3Al alloys, Foundry, 60(5), 489(2011)(周 伟, 彭晓东, 杨 艳, 刘华堂, Sr对Mg--9Li--3Al合金显微组织及高温力学性能的影响, 铸造, 60(5), 489(2011))9 H.Zhang, N.P.Jin, J.H.Chen, Hot deformation behavior of Al–Zn–Mg–Cu–Zr aluminum alloys during compression at elevated temperature, Nonferrous. Met., 21, 437(2011)10 H.Z.Li, H.J.Wang, X.P.Liang, H.T.Liu, X.M.Zhang, Hot deformation and processing map of 2519A aluminum alloy, Materials Science and Engineering A, 528, 1548(2011)11 X.D.Hung, H.Zhang, Y.Han, W.X.Wu, J.H.Chen, Hot deformation behavior of 2026 aluminum alloy during compression at elevated temperature, Materials Science and Engineering A, 527, 485(2010)12 HUANG Shiquan, YI Youping, LI Pengchuan, High temperature deformation behavior of 23Co13Ni11Cr3Mo ultrahigh strength steel, Chinese Journal of Materials Research, 25(5), 284(2011)(黄始全, 易幼平, 李蓬川, 23Co13Ni11Cr3Mo超刚强纲的高温变形行为, 材料研究学报, 25(5), 284(2011))13 ZHOU Dening, CHEN Zhiyu, HAN Ying, FAN Guangwei, ZHANG Wei, Study on constitutive models of 22Cr–5Ni–3Mo–N high alloy steel for high temperature deformation, Chinese Journal of Materials Research, 25(6), 591(2011)(邹德宁, 陈治毓, 韩 英, 范光伟, 张 威, 22Cr--5Ni--3Mo--N高合金钢高温变形本构模型研究, 材料研究学报, 25(6), 591(2011))14 Y.F Han, W.D.Zeng, Y.L.Qi, Y.Q.Zhao, Optimization of forging process parameters of Ti600 alloy by using processing map, Materials Science and Engineering A, 529,393(2011)15 Y.V.R.K, Prasad, K.P.Rao, Processing maps for hot deformation of rolled AZ31 magnesium alloy plate: Anisotropy of hot workability, Materials Science and Engineering A, 487, 316(2008)16 D.H.Li, Y.Yang, T.Xua, H.G.Zheng, Q.S.Zhu, Q.M.Zhang, Observation of the microstructure in the adiabatic shear band of 7075 aluminum alloy, Materials Science and Engineering A, 527, 3529(2010)17 L.Jiang, J.J.Jonas, R.K.Mishra, A.A.Luo, A.K.Sachdev, S.Godef, Twinning and texture development in two Mg alloys subjected to loading along three different strain paths, Acta Materialia, 55(1), 3899(2007)18 S.Anbuselvan, S.Ramanathan, Hot deformation and processing maps of extruded ZE41A magnesium alloy, Materials and Design, 31, 2319(2010)19 M.L.Ma, L.Q.He, X.G.Li, Y.J.Li, K.Zhang, Hot workability of Mg–9Y–1MM–0.6Zr alloy, Journal of Rare Earths, 29(5), 460(2011)20 M.M.Avedesian, H.Baker, ASM Specialty Hand–book–Magnesium and Magnesium Alloys (OH, ASM International, 1999) p.25821 P.Wang, L.H.Wu, S.K.Guan, Effect of initial microstructure on superplastic deformation of AZ70 magnesium alloy, Nonferrous Met., 20, 527(2010)22 R.Panicker, A.H.Chokshi, R.K.Mishra, Microstructure evolution and grain boundary sliding in a superplastic magnesium AZ31 alloy, Acta Materials, 57, 3683(2009)23 H.Watanabe, H.Tsutsui, T.Mukai, M.Konzu, S.Tanbe, K.Higashi, Deformation mechanism in a coarse–grained Mg–Al–Zn alloy at elevated temperatures, International Journal of Plasticity, 17, 387(2011)24 S.Tanabe, K.Higashi, The superplastic property of the as–extruded Mg–8Li alloy, Materials Science and Engineering A, 527, 3284(2011) |
No Suggested Reading articles found! |
|
|
Viewed |
|
|
|
Full text
|
|
|
|
|
Abstract
|
|
|
|
|
Cited |
|
|
|
|
|
Shared |
|
|
|
|
|
Discussed |
|
|
|
|