|
|
Impact Wear Behavior of a Novel Light-weight Austenitic Wear-resistant Steel |
Shiguang PENG1, Renbo SONG1, Changhong CAI1, Zhongzheng PEI1, Ke GUO2,3, Zhonghong WANG3, Jingjun GAO4 |
1 School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083, China 2 School of Chemical Engineering, University of Science and Technology Liaoning, Anshan 117022, China 3 Angang Group Mining Engineering Corporation, Anshan 114004, China 4 Anshan Iron and Steel Group Mining Company, Anshan 114001, China |
|
Cite this article:
Shiguang PENG, Renbo SONG, Changhong CAI, Zhongzheng PEI, Ke GUO, Zhonghong WANG, Jingjun GAO. Impact Wear Behavior of a Novel Light-weight Austenitic Wear-resistant Steel. Chinese Journal of Materials Research, 2017, 31(7): 537-546.
|
Abstract The wear resistance and wear mechanism of a novel light-weight Fe-24Mn-7Al-1.0C austenitic steel after water quenching (Q) and water quenching-aging (Q-A) treatments were studied by comparing with the Mn13Cr2. The impact wear tests were carried out by using MLD-10 abrasive wear testing tester under low impact energy condition (0.5 J). Results show that the wear resistance of Fe-24Mn-7Al-1.0C steel is 1.14 times higher than that of the water quenched Mn13Cr2. A large number of nano-sized (Fe, Mn)3AlC κ-carbide precipitates increase the initial hardness, strength and wear resistance of the steel after aging treatment at 550℃ for different time. The wear resistance of Fe-24Mn-7Al-1.0C steel is optimum after 1050℃ quenching and aging 1 h at 550℃, which is 1.40 times higher than that of Mn13Cr2. The worn surfaces of Mn13Cr2 consist of wide, long, uneven grooves and deep peeling pits, of which the formation may be ascribed to the repeated plastic deformation, while worn surfaces of the Fe-24Mn-7Al steel consist of tiny peeling pits and light grooves. Many stacking faults and dislocations in different directions are found on the subsurface of Mn13Cr2. Many Taylor lattices are found at the impact subsurface of Fe-24Mn-7Al steel before aging treatments. After aging treatment for 1 h at 550℃, Taylor lattices and high-density dislocations are found, but no twins and martensitic transformation appear on the worn surface.
|
Received: 11 July 2016
|
|
[1] | Yang F Q, Song R B, Li Y P, et al.Tensile deformation of low density duplex Fe-Mn-Al-C steel[J]. Mater. Des., 2015, 76: 32 | [2] | Zhang L F, Song R B, Zhao C, et al.Work hardening behavior involving the substructural evolution of an austenite-ferrite Fe-Mn-Al-C steel[J]. Mater. Sci. Eng., 2015, 640: 225 | [3] | Chen M S, Cheng H C, Huang C F, et al.Effects of C and Cr content on high-temperature microstructures of Fe-9Al-30Mn-xC-yCr alloys[J]. Mater. Charact., 2010, 61(2): 206 | [4] | Brüx U, Frommeyer G, Gr?ssel O, et al.Development and characterization of high strength impact resistant Fe-Mn-(Al-, Si) TRIP/TWIP steels[J]. Steel Res. Int., 2002, 73(6-7): 294 | [5] | Kalashnikov I S, Acselrad O, Shalkevich A, et al.Heat treatment and thermal stability of FeMnAlC alloys[J]. Mater. Process. Technol., 2003, 136(1-3): 72 | [6] | Sohn S S, Lee B J,Lee Set al. Effects of aluminum content on cracking phenomenon occurring during cold rolling of three ferrite-based lightweight steel[J]. Acta Mater., 2013, 61(15): 5626 | [7] | Wang C J, Chang Y C.NaCl-induced hot corrosion of Fe-Mn-Al-C alloys[J]. Mater. Chem. Phys., 2002, 76(2): 151 | [8] | Lins V F C, Freitas M A, Silva E M P E. Corrosion resistance study of Fe-Mn-Al-C alloys using immersion and potentiostatic tests[J]. Appl. Surf. Sci., 2005, 250(1-4): 124 | [9] | Yang F Q, Song R B, Sun T, et al.Microstructure and mechanical properties of Fe-Mn-Al light-weight high strength steel[J]. Acta Metall. Sin., 2014, 50(8):897(杨富强,宋仁伯,孙挺等. Fe-Mn-Al轻质高强钢组织和力学性能研究[J]. 金属学报, 2014, 50(8):897) | [10] | Cheng W C, Cheng C Y, Hsu C W, et al.Phase transformation of the L12 phase to kappa-carbide after spinodal decomposition and ordering in an Fe-C-Mn-Al austenitic steel[J]. Mater. Sci. Eng., 2015, 642: 128 | [11] | Wu Z Q, Ding H, An X H, et al.Influence of Al content on the strain-hardening behavior of aged low density Fe-Mn-Al-C steels with high Al content[J]. Mater. Sci. Eng., 2015, 639: 187 | [12] | Acselrad O, de Souza A R, Kalashnikov I S, et al. A first evaluation of the abrasive wear of an austenitic FeMnAlC steel[J]. Wear, 2004, 257(9-10): 999 | [13] | Abbasi M, Kheirandish S, Kharrazi Y,et al.On the comparison of the abrasive wear behavior of aluminum alloyed and standard Hadfield steels[J]. Wear, 2010, 268(1-2): 202 | [14] | Choi K.,Seo C. H.,Lee H.,et al.Effect of aging on the microstructure and deformation behavior of austenite base lightweight Fe-28Mn-9Al-0.8C steel[J]. Scr. Mater., 2010, 63(10): 1028 | [15] | Hwang C N, Liu T F.The as-quenched microstructures of Fe-9Al-30Mn-1.2C-xSi alloys[J]. Scr. Mater., 1997, 36(8): 853 | [16] | Park K, Hwang S W, Son C Y, et al.Effects of heat treatment on microstructure and tensile properties of a Fe-27Mn-12Al-0.8C low-density steel[J]. JOM, 2014, 66(9): 1828 | [17] | Lu Z, Zhou Y, Rao Q, et al.An investigation of the abrasive wear behavior of ductile cast iron[J]. J. Mater. Process Technol., 2001, 116(2-3): 176 | [18] | Zuidema B K, Subramanyam D K, Leslie W C.The Effect of Aluminum on the work hardening and wear resistance of Hadfield manganese steel[J]. Metall. Trans., 1987, 18A: 1629 | [19] | Talonen J, H?nninen H.Formation of shear bands and strain-induced martensite during plastic deformation of metastable austenitic stainless steels[J]. Acta Mater., 2007, 55(18): 6108 | [20] | Gutierrez-Urrutia I, Raabe D.Multistage strain hardening through dislocation substructure and twinning in a high strength and ductile weight-reduced Fe-Mn-Al-C steel[J]. Acta Mater., 2012, 60(16): 5791 | [21] | Bay B, Hansen N, Kuhlmann-Wilsdorf D.Deformation structures in lightly rolled pure aluminum[J]. Mater. Sci. Eng., 1989, 113: 385 | [22] | Hughes D A.Microstructural evolution in a non-cell forming metal: Al Mg[J]. Acta Metal. Mater., 1993, 41(5): 1421 | [23] | Yoo J D, Park K.Microband-induced plasticity in a high Mn-Al-C light stee[J]. Mater. Sci. Eng., 2008, 496(1-2): 417 | [24] | Allain S, Chateau J P, Bouaziz O, et al.Correlations between the calculated stacking fault energy and the plasticity mechanisms in Fe-Mn-C alloys [J].Mater. Sci. Eng., 2004, 387-389: 158 | [25] | Dumay A, Chateau J P, Allain S, et al. Influence of addition elements on the stacking-fault energy and mechanical properties of an austenitic Fe-Mn-C steel[J]. Mater. Sci. Eng., 2008, 483-484: 184 | [26] | Allain S, Chateau J P, Bouaziz O. A physical model of the twinning-induced plasticity effect in a high manganese austenitic steel [J]. Mater. Sci. Eng., 2004, 387-389: 143 | [27] | Karaman I., Sehitoglu H., Gall K.et al.Deformation of single crystal Hadfield steel by twinning and slip[J]. Acta Mater., 2000, 48(6), 1345 |
|
No Suggested Reading articles found! |
|
|
Viewed |
|
|
|
Full text
|
|
|
|
|
Abstract
|
|
|
|
|
Cited |
|
|
|
|
|
Shared |
|
|
|
|
|
Discussed |
|
|
|
|