Please wait a minute...
材料研究学报  2017, Vol. 31 Issue (7): 553-560    DOI: 10.11901/1005.3093.2016.571
  研究论文 本期目录 | 过刊浏览 |
含Ti铸造双相不锈钢点蚀行为研究
曹静(), 安立聪, 齐兴, 杨弋涛
上海大学材料科学与工程学院 上海 200072
Pitting Corrosion Behavior of Cast Ti-bearing Duplex Stainless Steel
Jing CAO(), Licong AN, Xing QI, Yitao YANG
School of Materials Science and Engineering, Shanghai University, Shanghai 200072, China
引用本文:

曹静, 安立聪, 齐兴, 杨弋涛. 含Ti铸造双相不锈钢点蚀行为研究[J]. 材料研究学报, 2017, 31(7): 553-560.
Jing CAO, Licong AN, Xing QI, Yitao YANG. Pitting Corrosion Behavior of Cast Ti-bearing Duplex Stainless Steel[J]. Chinese Journal of Materials Research, 2017, 31(7): 553-560.

全文: PDF(4907 KB)   HTML
摘要: 

借助电化学极化曲线以及阻抗法研究了合金元素Ti的加入对铸造双相不锈钢点蚀行为的影响,通过扫描电子显微镜(SEM)、能谱分析(EDS)以及X射线衍射(XRD)研究了铸造双相不锈钢在发生点蚀前后微观形貌、元素分布以及析出相种类的变化并探讨点蚀的萌生机制。结果表明:双相不锈钢中,点蚀主要发生在奥氏体相以及相界处,产生点蚀的原因是奥氏体相中富Cr区的存在以及相界碳化物的析出。在双相不锈钢中加入少量合金元素Ti,可以提高双相不锈钢的耐点蚀能力。

关键词 金属材料双相不锈钢点蚀交流阻抗合金元素    
Abstract

Effect of Ti addition on the pitting corrosion behavior of casting duplex stainless steel was studied by means of potentiodynamic measurement and impedance spectroscopy as well as scanning electron microscope (SEM) along with energy-dispersive spectroscopy (EDS) and X-Ray Diffractometer (XRD). It turned out that pitting corrosion occurred mainly on the austenite phase and phase boundaries because of the existence of Cr-rich zone and the precipitation of carbides in the austenite phase and at phase boundaries respectively. Pitting corrosion resistance of duplex stainless steel could be improved through the addition of Ti.

Key wordsmetallic materials    duplex stainless    steel    pitting corrosion,EIS    alloying elements
收稿日期: 2016-09-29     
ZTFLH:  TG172  
作者简介:

作者简介 曹 静,女,1993年生,硕士生

Samples C Si Mn Cr Mo Ni Nb Ti N Fe
1# 0.31 1.27 1.78 27.5 1.50 9.26 0.27 0 0.03 Bal.
2# 0.32 1.09 1.72 27.8 1.41 9.37 0.29 0.23 0.02 Bal.
3# 0.28 1.07 1.71 27.6 1.44 9.34 0.28 0.67 0.04 Bal.
表1  双相不锈钢的化学成分
图1  不同样品的电化学极化曲线
Samples Content of Ti Ecorr /V Icorr/μAcm-2 Ep/V Ep-Ecorr/V Rp/kΩcm2
1# 0 -0.275 167 -0.106 0.169 54.7
2# 0.23 -0.223 48.3 -0.004 0.219 85.9
3# 0.67 -0.200 23.6 0.078 0.278 276.6
表2  动电位极化曲线拟合获得的电化学参数
图2  三种试样的电化学阻抗谱图
图3  等效电路模型
Samples Rs/Ωcm2 Y0/S-secn/cm2 n Rct/Ωcm2
1# 5.60 6.05×10-5 0.89 4.83×104
2# 5.59 4.98×10-5 0.89 8.51×104
3# 6.62 3.98×10-5 0.88 2.93×105
表3  拟合实验数据获得的等效电路参数
图4  不同样品的显微结构
Ti/%, mass fraction 0 0.2 0.6
Content of δ phase/% 46 53 58
表4  不同样品铁素体含量
图5  不同样品的腐蚀形貌
图6  不同样品的点蚀形貌
图7  3#样品的相界元素分布
Samples Cr23C6 Nb4C3 (Nb,Ti)C TiN
1# 88.1 11.9 0 0
2# 86.1 0 11.2 2.7
3# 70.5 0 27.3 2.2
表5  不同析出相质量百分比
图8  萃取物XRD图谱
图9  双相不锈钢点蚀产生示意图
[1] Mao X P, Wang G, Ma Z Y.The development of materials of supercritical units or ultra supercritical units[J]. Mod. Electr. Power, 2005, 22(1): 69(毛雪平, 王罡, 马志勇. 超超临界机组汽轮机材料发展状况[J]. 现代电力, 2005, 22(1): 69)
[2] Lang X, Zhao L, Wang J C, et al.Advances in research and application of duplex stainless steel for marine castings in China[J]. Foundry, 2011, 60: 459(朗宵, 赵岭, 王景成等. 我国船用铸造双相不锈钢的研究和应用进展[J]. 铸造, 2011, 60: 459)
[3] El-Batahgy A, Zaghloul B.Fatigue failure of an offshore condensate recycle line in a natural gas production field[J]. Mater. Charact., 2005, 54: 246
[4] Zhang G X, Li S Q.Performance of duplex stainless steel and its application in petrochemical industry[J]. Petro Chem. Equip. Technol., 2007, 28(4): 63(张国信, 李双权. 双相不锈钢的性能及其在石化行业的应用[J]. 石油化工设备技术, 2007, 28(4): 63)
[5] Pohl M, Storz O, Glogowski T.Effect of intermetallic precipitations on the properties of duplex stainless steel[J]. Mater. Charact., 2007, 58(1): 65
[6] Wu Z Z, Song Z G, Zheng W J, et al.Effect of solution temperature on microstructure and pitting corrosion resistance property of super duplex stainless steel 00Cr25Ni7Mo4N[J]. Heat Treat. Metals, 2007, 32(8): 50(吴忠忠, 宋志刚, 郑文杰等. 固溶温度对00Cr25Ni7Mo4N超级双相不锈钢显微组织及耐点蚀性能的影响[J]. 金属热处理, 2007, 32(8): 50)
[7] Wang Y Q, Lin S H, Li N, et al.Overview of σ phase influencing on mechanical properties of stainless steels[J]. J. Iron Steel Res., 2016, 28(2): 1(王永强, 林苏华, 李娜等. σ相析出对不锈钢力学性能的影响概述[J]. 钢铁研究学报, 2016, 28(2): 1)
[8] Lippold J C, Kotecki D J.Welding Metallurgy and Weldability of Stainless Steels[M]. New York: John Wiley & Sons Inc., 2005
[9] Gholami M, Hoseinpoor M, Moayed M H.A statistical study on the effect of annealing temperature on pitting corrosion resistance of 2205 duplex stainless steel[J]. Corros. Sci., 2015, 94: 156
[10] Lopez N, Cid M, Puiggali M.Influence of o-phase on mechanical properties and corrosion resistance of duplex stainless steels[J]. Corros. Sci., 1999, 41(8): 1615
[11] Nilsson J O, Kangas P, Wilson A, et al.Mechanical properties, microstructural stability and kinetics of σ-phase formation in 29Cr-6Ni-2Mo-0.38N superduplex stainless steel[J]. Metall. Mater. Trans., 2000, 31A: 35
[12] Gu Y, Zhan Z L, Rong F.Effect of Nb and Ti on the toughness of 445M ferritic stainless steel[J]. J. Iron Steel Res., 2012, 24(1): 31(顾玥, 詹肇麟, 荣凡. 铌、钛对445M铁素体不锈钢韧性的影响[J]. 钢铁研究学报, 2012, 24(1): 31)
[13] Moayed M H, Newman R C.Deterioration in critical pitting temperature of 904L stainless steel by addition of sulfate ions[J]. Corros. Sci., 2006, 48(11): 3513
[14] Ye C, Du N, Zhao Q, et al.Progress in research of pitting corrosion behavior and research methods of stainless steels[J]. Corros. Protect., 2014, 35: 271(叶超, 杜楠, 赵晴等. 不锈钢点蚀行为及研究方法的进展[J]. 腐蚀与防护, 2014, 35: 271)
[15] Kim S T, Jang S H, Lee I S, et al.Effects of solution heat-treatment and nitrogen in shielding gas on the resistance to pitting corrosion of hyper duplex stainless steel welds[J]. Corros. Sci., 2011, 53(5): 1939
[16] Zheng C B, Shen X L, Tang Z J.Effect of solution treatment temperature on phase structure and corrosion resistance of 2507 duplex stainless steel[J]. Heat Treat. Metals, 2015, 40(8): 124(郑传波, 申小兰, 唐祝君. 固溶温度对2507双相不锈钢组织与耐蚀性能的影响[J]. 金属热处理, 2015, 40(8): 124)
[17] Yan W, Shan Y Y, Yang K.Effect of TiN inclusions on the impact toughness of low-carbon microalloyed steels[J]. Metall. Mater. Trans., 2006, 37A: 2147
[18] Tian J X, Zhang C, Wang H P, et al.Effect of Nb, Ti on pitting corrosion resistant of high-pure ferritic stainless steel, edited by Steelmaking Committee [A]. The 17th CSM Annual Steel Making Conference Proceedings (Part B)[C]. Hangzhou: The Chinese Society for Metals, 2013(田俊行, 张驰, 王宏坡等. Nb、Ti对高纯铁素体不锈钢耐点蚀性能的影响 [A]. 第十七届全国炼钢学术会议论文集(B卷)[C]. 杭州: 中国金属学会, 2013)
[19] Macdonald D D.The point defect model for the passive state[J]. J. Electrochem. Soc., 1992, 139: 3434
[1] 毛建军, 富童, 潘虎成, 滕常青, 张伟, 谢东升, 吴璐. AlNbMoZrB系难熔高熵合金的Kr离子辐照损伤行为[J]. 材料研究学报, 2023, 37(9): 641-648.
[2] 宋莉芳, 闫佳豪, 张佃康, 薛程, 夏慧芸, 牛艳辉. 碱金属掺杂MIL125CO2 吸附性能[J]. 材料研究学报, 2023, 37(9): 649-654.
[3] 赵政翔, 廖露海, 徐芳泓, 张威, 李静媛. 超级奥氏体不锈钢24Cr-22Ni-7Mo-0.4N的热变形行为及其组织演变[J]. 材料研究学报, 2023, 37(9): 655-667.
[4] 邵鸿媚, 崔勇, 徐文迪, 张伟, 申晓毅, 翟玉春. 空心球形AlOOH的无模板水热制备和吸附性能[J]. 材料研究学报, 2023, 37(9): 675-684.
[5] 幸定琴, 涂坚, 罗森, 周志明. C含量对VCoNi中熵合金微观组织和性能的影响[J]. 材料研究学报, 2023, 37(9): 685-696.
[6] 欧阳康昕, 周达, 杨宇帆, 张磊. LPSOMg-Y-Er-Ni合金的组织和拉伸性能[J]. 材料研究学报, 2023, 37(9): 697-705.
[7] 徐利君, 郑策, 冯小辉, 黄秋燕, 李应举, 杨院生. 定向再结晶对热轧态Cu71Al18Mn11合金的组织和超弹性性能的影响[J]. 材料研究学报, 2023, 37(8): 571-580.
[8] 熊诗琪, 刘恩泽, 谭政, 宁礼奎, 佟健, 郑志, 李海英. 固溶处理对一种低偏析高温合金组织的影响[J]. 材料研究学报, 2023, 37(8): 603-613.
[9] 刘继浩, 迟宏宵, 武会宾, 马党参, 周健, 徐辉霞. 喷射成形M3高速钢热处理过程中组织的演变和硬度偏低问题[J]. 材料研究学报, 2023, 37(8): 625-632.
[10] 由宝栋, 朱明伟, 杨鹏举, 何杰. 合金相分离制备多孔金属材料的研究进展[J]. 材料研究学报, 2023, 37(8): 561-570.
[11] 任富彦, 欧阳二明. g-C3N4 改性Bi2O3 对盐酸四环素的光催化降解[J]. 材料研究学报, 2023, 37(8): 633-640.
[12] 王昊, 崔君军, 赵明久. 镍基高温合金GH3536带箔材的再结晶与晶粒长大行为[J]. 材料研究学报, 2023, 37(7): 535-542.
[13] 刘明珠, 樊娆, 张萧宇, 马泽元, 梁城洋, 曹颖, 耿仕通, 李玲. SnO2 作散射层的光阳极膜厚对量子点染料敏化太阳能电池光电性能的影响[J]. 材料研究学报, 2023, 37(7): 554-560.
[14] 秦鹤勇, 李振团, 赵光普, 张文云, 张晓敏. 固溶温度对GH4742合金力学性能及γ' 相的影响[J]. 材料研究学报, 2023, 37(7): 502-510.
[15] 刘天福, 张滨, 张均锋, 徐强, 宋竹满, 张广平. 缺口应力集中系数对TC4 ELI合金低周疲劳性能的影响[J]. 材料研究学报, 2023, 37(7): 511-522.